FAQ

Why Do I Need a Repiping?

You will need Repiping because:
  • Leaking
Once the pipe starts to leak, this is usually a sign that your pipe is starting to wear out and they need to be replaced as soon as possible. Pipes leaked so badly to the point that they started to get holes because the metal was very thin in the areas. When a pipe starts to leak, you can usually expect most of the pipes in your home to follow.
  • Water changes
When water from your side starts to look strange, it is usually caused by severe rust in your pipe. This can actually be a health hazard and you should not drink water. Replace your pipe as soon as possible because you can expect a bigger problem to begin immediately.
  • Lower Water Pressure
Another sign that your pipe is damaged and needs to be replaced is if you see a lack of water pressure from what you saw in the past. Your pipes may be rusty, making it difficult for water to pass through, or they may collapse on their own. Don’t wait to replace the pipe if this happens!
  • Wall Damage
If the walls or parts of your house are seriously damaged, your pipes will definitely be affected. They will also suffer damage, and most people will only replace their pipes at that time instead of waiting for them to be damaged. Sometimes, this damage can even cause intense vibrations that break some of your pipes into impact.
  • Preparing for the Future
The last common reason that someone will recreate their home is to prepare for the future so they don’t have to do it later. These are only security precautions.

How Much Average Of Plumbing Cost Per Service?

The average commercial plumber costs around $45 to $200 per hour and a housing plumber is $175 to $450 per hour. Fixed Plumber Plans will charge you based on the type of service as a task they have done. An hourly plumber will charge based on the total number of hours needed to complete the work.

How to Remove Grease Drain?

How to remove your grease drain :

  • Boil water and mix 1 part hot water and 1 part vinegar.
  • Pour the mixture into your kitchen drain and let it sit for a few minutes.
  • Hot water will help melt the oil, while vinegar will eat the oil attached to the pipe.
  • After pouring the mixture of hot water and vinegar into the drain, follow it with boiling water. Boiling water must water the remaining oil from your pipe.
  • Clogged drains can emit a terrible odor that tends to be left in your kitchen for some time.
  • To neutralize the odor that comes from your sewer, mix 1 part hot water and 1 part bleach, then pour the mixture into the drain. Continue with warm soapy water.
  • Ways to deal with oil in your sewer must make everything flow again. Remember to take steps to prevent future blockages.

How to Get Rid Roots in Drain?

Tips to get rid of roots in your drain are:

  • The first way to get rid of the root of your toilet is to pour some sodium chloride or copper sulfate, or rock salt, into the toilet covered with roots, chemical reactions will help drain your toilet clean from the roots.
  • In addition, you can also use this method by using a foamy root killer, in addition to cleaning the roots, this method also helps prevent the roots from growing back in your pipe to do this process once a year to prevent the roots from growing back.

The above 2 methods are very effective for cleaning and maintaining the cleanliness of your toilet from the roots. In addition, these compounds are also very effective in sucking moisture from the roots.

How to Fix Low Water Pressure?

Usually, low water pressure is a problem with only one fixture and is the result of mineral buildup. Mineral deposits look like white, off-white, or blue-green crust which can be seen in pipes or outside of water equipment in their joints.This deposit can be easily cleaned by doing these steps:

  • First take a clean cloth
  • Soaking a clean cloth in white vinegar and wrapping it around the affected area.
  • Secure the fabric with a rubber band and let it sit for one hour.
  • The sink and shower faucets and outdoor taps contain a section called an aerator, a net-like cover that combines air with water to create a spark-free flow. These parts can be removed and soaked in equal parts with white vinegar and water to remove mineral buildup.

What Type of Water Heater I Should Choose?

Before you choose your heat water types, you must answer this question to decidee which one types will fit in. Question likes :

  • Which of the following best describes your climate?
  • How many people live in your household
  • Your water heater is currently supported by …
  • How do you describe the quality of your water?
  • How important is it for you that buying your new tool helps reduce your electricity bill?
  • How much are you willing to spend up front for a new water heater?
  • How long do you anticipate staying in your current home?

By answers that question you easily can choose types of your water heater :

  • Water Heater Storage Tank
  • Tankless Water Heaters
  • Hybrid / Hot Pumps

What Is The Solution of Frozen Pipes?

  • First thing before doing anything, turn off the water supply to the plumbing section (or the whole house if it’s the only choice) because the real problem starts after liquefaction.
  • That’s because frozen water might act as a plug, preventing water from spilling from cracks in your pipe. When the plug is thawed, water spurts out.
  • Prepare mops, buckets and towels in case there is a pipe leak.
  • Use a heater, a heat lamp, or a hair dryer to melt a frozen pipe.
  • Wrapping a frozen pipe with a heat band that is thermostatically controlled (from $ 50 to $ 200, depending on the length) is also an effective way to quickly dilute the problematic place.
  • Do not melt the pipe using a propane torch, which presents the risk of fire.

What Plumbing Service I Can DIY And I Should Call Professional Plumber?

  • Call Pro if the cable or electricity is involved. If you don’t have experience with cables and electricity, don’t put yourself, your family or home at risk. Bring licensed and bound professionals who know the cables.
  • DIY if your tub or sink is clogged. Pull the outlet plug and feed the spout snake under the pipe. If you don’t have one, straighten the clothes hanger. Rotate the instrument of your choice and release it slowly, chances are that your hair will close and accumulate. Repeat this process several times, then continue with the drain and hot water cleaner.
  • Call Pro if your pipe freezes. Trying to dilute your own pipe, you run the risk of further damage. Professional plumbers are trained to properly close cracks in the pipe.
  • DIY if your toilet overflows. Behind the toilet, near the floor, there is a water cutoff valve. Turn to the right to keep the water from rising higher. Open the tank and lift the floating ball to give it time to flow.
  • Call Pro if your backup toilet is stubborn. The problem might lie deeper in the drain, which might require some digging to fix it. Before you tear your page, make a call.
  • DIY if your sink stopper breaks, leaving your sink full of dirty water without a way to drain it. Don’t be afraid: there is a lever under the sink that controls the stopper. The pivot bar connects the water channel to the handle. Press down on the end of the rod near the handle to lift the plug. After your sink is drained, don’t hesitate to find a cheap stopper replacement.
  • Call Pro if the part needs to be replaced. If something complicated like a water heater or a water pump doesn’t work, it can mean you need a new part of it.